Two (2) New Side-Loading, 27 yard, Sanitation Trucks
| Bidders ID: | NBD15839432005867163 |
|---|---|
| Due Date: | Jul 30, 2026 |
| Posted Date: | Jul 1, 2026 |
| Level of Government: | State & Local |
| State: | Wyoming |
| Agency: | City of Casper |
| Category: |
|
| Source: | Members Only |
| Description | Opening Date/Time | Closing Date/Time |
|
Two (2) New Side-Loading, 27 yard, Sanitation Trucks |
July 01, 2026 8:00 AM |
July 30, 2026 3:15 PM |
Attachment Preview
CITY OF CASPER
FLEET MAINTENANCE DIVISION
CITY OF CASPER
(307) 235-8410
July 1, 2026
Notice is hereby given that the City of Casper, Wyoming will receive sealed bids at the Fleet Office, Casper
Service Center, 1800 E. “K” Street, Casper, Wyoming, until 3:15 p.m., July 30, 2026 for the following:
TWO (2) NEW SIDE-LOADING, 27 YARD, SANITATION TRUCK. This unit will be used by the Solid
Waste Division of the Public Services Department; unit must have the minimum specifications of:
General
Specifications:
ITEM
It is the intent of this specification to specify the minimum requirement for the furnishing
and delivery of TWO (2) new side-loading, 27-yard, sanitation truck. The unit shall be
new and have less than one hundred fifty (150) hours. This unit shall be less than twelve
months old, with full factory warranty. Units shall be delivered complete and ready for
service, as specified, and shall be equipped with all of the manufacturer’s standard
equipment, as advertised, whether or not specifically mentioned in these specifications,
in addition to all other equipment and attachments specified herein.
BIDDERS
MINIMUM SPECIFICATIONS
SPECIFICATIONS
1. GVW
2. Wheel
Base
3. Cab to
Axle
Manufactured in the USA 66,000 pound minimum.
Certified GVW Cab and Chassis.
Shall be compatible with a 27-cu. yd. Zero Radius
Chain Driven Arm side-loading body. Minimum
acceptable wheel base shall not be less than 200".
Equipment supplied shall provide proper weight
distribution when truck is loaded.
195" useable minimum and 210” useable maximum.
Shall be compatible with a 27-yard Zero Radius
Chain Driven Arm side-load body (see body
required specifications.) It shall also provide proper
weight distribution when truck is loaded.
4. Frame
35 SM, 120,000 psi, double-channel rails after
frame shall be a minimum of 96". Frame shall
extend 5' behind suspension for hinge point of body.
R.B.M. 2,075,000 in-lb. Deep frame section
3,200,000 in-lb. (minimum). Bolt-on extensions
will not be accepted.
5. Diesel
Engine
Current year production model diesel cummings
engine. 2027 emission compliant, 350 gross
horsepower, torque 1,350 ft. lb. Engine block
heater. Intake air pre-heater. Shall have a Davco
382 heated fuel/water separator.
1
ITEM
MINIMUM SPECIFICATIONS
BIDDERS
SPECIFICATIONS
6. Power Take-Off Transmission mounted piston pump. Pump limiter
Front-Mount shall be connected to engine computer not external
Pump
over-speed box. Truck supplier shall work with
body supplier on this function.
7. Cooling
System
8. Transmission
9. Axles
10. Springs
11. Tires and
Rims
Coolant hoses – shall be silicone rubber including
heater hoses. Heavy-duty radiator shall be
protected to -34° F with year-round extended life
coolant. An integral transmission cooler shall be
provided. Coolant recovery tank provided to
maintain necessary operating temperatures @ 5,500
ft. elevation, with 100+ degree daytime
temperatures.
Fully automatic, 6-speed Allison H.D. 4500-RDS-6
Rugged Duty Series Gen. 5. The transmission
controls shall be Allison electronic pushbutton with
shift shock eliminator. Controls shall be on right
hand side of cab.
Front - 20,000 lbs. capacity (minimum).
Front axle shall have a minimum setback
comparable or equal to current City of Casper
sanitation trucks.
Notice to Bidders: Truck must be delivered,
equipped, and bid with a 27-yard, side-load, refuse
body.
Rear - 46,000 lbs. capacity (minimum). Spring
suspension type with inter-axle lock and full wheel
lock, or equivalent, top speed not to exceed 70
MPH.
Front - 20,000 lbs. ground capacity (minimum).
Heavy duty double acting shock absorbers.
Rear - 46,000 lbs. ground capacity (minimum).
Shall be top spring configuration. Mack M-Ride or
equivalent.
Front - 315/80R22.5, 20 ply, Bridgestone M870 on
22.5 x 13 stud aluminum rims.
2
ITEM
12. Brakes
13. Cab
MINIMUM SPECIFICATIONS
Rear - 11R 22.5, 20 ply, Bridgestone L320 on 22.5
x 8.25 aluminum rim.
Note: Tires and rims are to meet the required GVW
rating regardless of specification.
Meritor Air Disc Brakes front and rear or
equivalent. Meritor brand automatic slack adjusters
with removable pawl for adjustment. Rotors, Brake
Pads, compressor, and accessories as required shall
meet all Federal Motor Vehicles Safety Standards.
Low air pressure buzzer and light. A Meritor
Wabco air dryer (ADIP) with heater. Air tanks
shall be steel (DOT) approved with petcock drain
valves. Auto drain valve on heated supply tank.
Two (2) man, LOW ENTRY, cab-over design with
tilt cab, steel body front of door hinges, power
windows both sides. Single step entry (ground to
step) step to floor. No additional steps will be
accepted. Floor of cab and single step must both
be enclosed in cab. No external step will be
accepted. High visibility tilt cab with “B” pillar
wrap around corner windows, and outer grab
handles for ease of ingress and egress on both driver
and passenger sides. Right hand side operator
configuration.
Both driver and passenger seats shall be a triple
lumbar, air ride suspension seats. They shall be
mounted on the left and right sides of cab. Engine
cover shall be recessed or low profile to
accommodate the ergonomic positioning of the
loader controls.
Insulated rubber floor mat.
Safety glass in all windows.
Arm rests left and right.
Two (2) belt-type seatbelts.
Dome light door operated.
H.D. cab trim.
AM/FM/ Bluetooth radio.
3
BIDDERS
SPECIFICATIONS
ITEM
MINIMUM SPECIFICATIONS
Front and rear mud flaps. Steel guard in front of
rear duals.
Power Door locks if available.
Electric or air operated cab jack with manual
backup.
Audibles to shut off when vehicles is put into
Reverse.
Red Dot 12-volt 22,000 BTU part # R-9727 roof
mounted A/C unit, and the stock A/C unit.
BIDDERS
SPECIFICATIONS
14. Steering
15. Fuel
Tank
16. Electrical
Steering shall be heavy-duty power steering at right
side operator position in cab. Steering tilt and
telescoping adjustment.
Left side mounted Aluminum, 75-gallon minimum
capacity, DOT approved with shut-off valve.
Mounted as far forward as possible. Contact body
supplier for placement. Do not mount fuel tank or
DEF tank under clean-out doors/troughs.
12-volt neg. ground.
165-amp alternator.
Three (3) 1,000/3,000 cca batteries.
Five (5) LED amber marker lights on cab.
Body will have LED lighting, chassis and body
shall be compatible.
Dimmer switch on steering column.
Turn signals with four-way emergency flashers.
Three sets of keys.
BATTERY SHUT-OFF SWITCH: easy to see and
easy to access.
Backup alarm system 107dB SAE Type B fully
sealed and wired into vehicle backup system.
4
ITEM
MINIMUM SPECIFICATIONS
All lighting shall be LED where available.
17. Mirrors
Two (2) bracket mirrors, LH/RH motorized and
heated, stainless steel clamp on type both left and
right hand. Shall be breakaway type and both
mirrors will have an 8” circular convex mirror
attached below lower arm.
18. Exhaust
System
Must meet all federal standards and be installed to
accommodate the 27-cu. yd. Zero Radius
Chain Driven Arm side-loading refuse body. To be
2023 emission certified, SCR catalyst type, passive
regeneration system and to be equipped with proper
protection to prevent burns (exhaust shield).
Perforated exhaust extension mounted on top of
exhaust pipe.
19. Gauges and
All critical controls required to operate the vehicle
Indicators in Cab from the right operator location. Gauges to be
mounted on right hand side of cab.
Fuel Gauge
Def Gauge
Oil pressure
Inter-axle differential lock indicator light
Volt meter
Air restriction indicator on air cleaner
Regeneration initiate/inhibit switch
Water temperature
Transmission temperature
Hour meter
Air pressure with air parking brake, on the right side
of cab.
Tachometer (electric)
Electric speedometer/odometer
Fuel Gauge
5
BIDDERS
SPECIFICATIONS
You are viewing the opportunity summary page, which includes a brief overview and a preview of the attached documents.
Disclaimer: The details regarding bids, requests for proposals (RFPs), and requests for qualifications (RFQs) on this site are provided for convenience and do not represent official public notice. To respond to or inquire about bids, RFPs, or RFQs, please contact the appropriate government department.
TRY FOR FREE
Not a GovernmentBidders Member Yet?
Get unlimited access to thousands of active local, state and federal government bids and awards in All 50 States.